CROSSRAM PARTS

Short style air filter used with wide base or standard base.

Email thepartsman@blastcomm.com for Price Quote

Tall style air filter used with wide base or standard base.

Email thepartsman@blastcomm.com for Price Quote

This is the bracket used by the factory to mount the alternator to the Cross Ram Intake.

Email thepartsman@blastcomm.com for Price Quote

This is the correct GM 3927140 Cam used on the Cross Ram cars RPM range is 4200-7200 with compression ratio of 11.0:1-12.5:1, includes lifter set.

Email thepartsman@blastcomm.com for Price Quote

Factory Holley Carburetor this is the original style carb used by GM with the Cross Ram setup, 600CFM.

Correct double size threaded studs used to bolt the Cross Ram carbs to the intake top plate (includes nuts not shown). One side is intake side and one side is carb side.

Correct studs and wing nuts for use on the Cross Ram Carbs, 2 studs and 2 wing nuts.

This is the brass block that is silver cadmium plated that allows all of the carb lines to be connected to the incoming fuel line. (Comes in the line and block kit also).

This is just the fuel lines for the Cross Ram setup no block included (Original Material).

This is just the fuel lines for the Cross Ram setup no block included (Stainless Steel).

This is just the fuel lines for the Cross Ram setup with fuel block included.

Fiberglass Factory Cross Ram Hood mounts directly to the factory hood hinges you must use the hood prop rod or use a pair of light weight hood springs.

Freight charges will be billed on a separate PayPal invoice after purchase of this item is complete.

Estimated freight charges to a zoned business address is around $160.00.

Estimated freight charges to a zoned residential address is around $175.00.

Contact thepartsman@blastcomm.com for more information on shipping.

This is a factory GM style hood prop rod used with a Cross Ram hood.

This fitting screws on the intake top plate and allow you to get vacuum to the distributor, cowl and PCV.

Factory throttle cable with correct end manufactured to OEM specifications, cable is 28” long.

This is the bracket that mounts on the intake between both carbs to hold and mount the throttle cable to the intake.

Factory linkage with ball joint ends used to connect throttle from the front carb to the rear carb.

When using a Cross Ram this is the factory pedal assembly used to connect the throttle cable to the accelerator pedal.

This is the throttle return spring that attach to the front carb throttle arm to the throttle return tab on the intake.

This is the bracket that mounts on the front of the intake and attaches the throttle return spring from the carb to the intake.

Correct set of TR bolts used to attach the Cross Ram water neck to the intake.

This is the plug that screws into the water neck to block off one of the ports.

This is a replacement water neck used on cross ram cars.

Correct Cross Ram air cleaner base, lid and short style air filter.

This is the plug that pushes into the intake when you don’t use the oil filler tube.

Assembly comes complete with:

The 2 Piece Intake (upper GM#: 3941130 and lower Gm#: 3941126) which has the correct (W) with Snowflake design that is a registered with the United States Trademark and Patent Office; this is the same mark used by the Winters Foundry when they produced this intake for General Motors, the date code on the intake is 11-25-68, also comes with the Water Neck, Water Neck Bolts, Water Neck Hex Plug, Throttle Linkage, Throttle Return Spring, Throttle Cable Bracket, Throttle Return Spring Tab Bracket, PCV Fitting, Filler Plug Block off Plate, Fuel Block, Fuel Lines, Fuel Block and Fuel Line Kit, Carburetor Studs, 2 Holley 4295 (GM#: 3957859) Carbs, the date code on the carbs is 891, Carb Studs with Wing Nuts and the Cross Ram Wide Base Air Cleaner Assembly (air cleaner base, lid and short style air filter).